Dinan

D760-0037

Dinan Carbon Fiber Cold Air Intake for BMW F06 F12 F13 M6

Product Description
The F06/12/13 M6 Cold Air intake is in compliance with U.S. EPA Memorandum 1A, or this product has not been found, nor is believed to be, unlawful for use under the provisions of the Clean Air Act. Currently: This product is not legal for sale or use in California, or states that have adopted California emissions standards, on any pollution controlled motor vehicles. 

 

The F06/12/13 M6 Dinan high flow carbon fiber cold air intake, like most Dinan products, has a sleek and functional appearance that embodies high performance. The F06/12/13 M6 cold air intake allows cool outside air to be pushed into the engine via a pair of supplemental carbon fiber intake ducts located at the front of the engine bay. Each duct leads combustion air through a custom designed intake assembly that has a larger than stock metered air flow housing, as well as a Dinan conical air filter with a 77% larger capacity.

 The stock air inlets are left intact and fully functional to provide a new total of four air intakes into the engine for maximum airflow. Improved induction airflow offered by Dinan cold air intake systems increase engine performance, even more so if used in combination with other performance enhancing Dinan products.

Benefits of Dinans Cold Air Intake:

+ Maximum peak power of 693 HP and 651 lb-ft of Torque utilizing Dinan Stage 2 components (DINANTRONICS™ Performance Tuner, intake and exhaust). A difference of 13 HP and 7 lb-ft of torque from Dinan Stage 1 (D-TRONICS Performance Tuner Only). 
+ Dinan proprietary Injection molded Dinan MAF housings are larger than stock
+ Stock air filters are replaced with 77% larger Dinan conical air filters.
+ Entire Dinan Intake system is sealed like a factory replacement to ensure only cold outside air and not hot air from the engine compartment is being utilized.
+ Stock System Stays Completely Functional
+ Carbon fiber air box lids and intake ducts
+ Raised Dinan logos are laminated into the carbon fiber intake
+ Rubber hoses, mounting brackets, & hardware included.

Also Recommended:

Free Flow Stainless Exhaust (D660-0049 & D660-0049-BLK): An important addition for any enthusiast who wishes their car to sound as good as it performs while also supplying significant power gains itself. These exhausts are dyno tested for maximum exhaust flow with minimum backpressure. The system is designed to provide a more aggressive sound under acceleration, while reducing drone inside the vehicle, thanks to Dinan’s exclusive Helmholtz Chamber and Butterfly Valve technologies.

DINANTRONICS Performance Tuner (D440-1603-ST1 & D440-1603-ST2):  The DINANTRONICS™ Performance Tuner is a highly engineered and sophisticated piece of computer hardware and software that enhances engine performance, without negating or voiding your new car warranty coverage and without affecting long term reliability or the functionality of on-board diagnostic systems. It is also the only tuning device emissions legal in all 50 states. The ultimate objective of developing this piece of technology was to provide the ability to control every signal entering and exiting the BMW factory Engine Control Unit. These items are unique to Dinan and together they embody the apex of performance engineering in a powerful, reliable, and warrantied package. 

DOWNLOAD INSTALLATION INSTRUCTION HERE

Not legal for sale or use in California. 

 MODELS SUPPORTED:
  • 2013-2018 M6 F06 Gran Coupe 
  • 2012-2018 M6 F12 Convertible 
  • 2012-2017 M6 F13 Coupe 
Product Specifications
Labor Hours/Installation Hours 6.00
Emission Status Emissions legal in most states --This product is in compliance with U.S. EPA Memorandum 1A, or this product has not been found, nor is believed to be, unlawful for use under the provisions of the Clean Air Act. Currently: This product is not legal for sale or use in California, and states that have adopted CA emissions standards, on any pollution controlled motor vehicles.
Peak Horsepower 693
Peak Torque 651
Required Items Installation requires specialized Dinan tool kit, DT763-0083 or DT763-0082 (F10 550)