CONCERNS ABOUT FITMENT?

The MMX Performance F8X front pair upgrades the supported 380 x 30mm steel-brake setup. Floating hats and directional curved vanes address heat handling while retaining the matching original calipers. The package includes separate left and right rotor assemblies.Key features Two-piece floating front discs with...

These MMX Performance rear rotors retain the supported factory caliper arrangement with a floating two-piece construction. The 370 x 24mm left- and right-handed discs use directional cooling vanes and aluminum hats. Match the original brake size, not only the model name.Key features Two-piece floating...

This MMX Performance B58 kit pairs a dual-entry cotton-gauze filter with shaped intake pipework. Billet brackets and rubber isolators support the assembly without making engine movement a rigid connection. The included hardware supports a reversible installation on the specified F-series applications.Key features Dual-entry cotton-gauze...

The S63 uses two charge coolers, and MMX Performance upgrades both sides in this set. Larger stepped cores, internal turbulators and cast end tanks address charge-air temperature while managing pressure loss. Factory-style installation keeps the work focused on cooling rather than fabrication.Key features Twin...

Track use and slow traffic can challenge gearbox cooling in different ways. The MMX Performance DCT oil cooler replaces the supported original transmission cooler. It is specific to the DCT setup, not an engine-oil cooler or manual-gearbox accessory.Key features Replacement cooler for the supported...

The X06 is a six-spoke flow-formed wheel for supported platforms. This package contains four wheels, not a single wheel. Choose gloss black, gloss gunmetal or gloss silver while keeping the same 18x8 dimensions and ET44 offset.Key features Six-spoke X06 design with flow-formed construction. Three...

This MMX Performance carbon intake changes the airbox system rather than only replacing connecting pipes. Its 3K twill carbon construction uses no fiberglass, with more filter area and revised intake paths. Gloss and matte options change the visible finish without changing the hardware concept.Key...

The three-point MMX Performance kit pairs a front differential cradle with one raised rear bush. It is the smaller G8X mounting package, with standard-height and 10mm lifted settings. Choose the four-point kit when adding the second rear mounting location is part of the plan.Key...

This MMX Performance kit supports the G8X differential at four matched points. A front cradle, dual rear mount and two raised bushes work at OEM height or a 10mm lifted setting. This is the mounting package; the sump and heat shields remain separate additions.Key...

The MMX Performance F8X dual mount uses the unused second rear mounting point to support the differential. It can stay at OEM height or join a matched raised arrangement with the front cradle. Start with movement control, adding geometry correction only when the rest...

Complete the supported G8X steel-brake setup with a directional rear rotor pair. These MMX Performance 370 x 24mm discs use floating two-piece construction and curved cooling vanes with matching OEM calipers. Separate left and right assemblies ensure correct directional installation.Key features Floating two-piece construction...

MMX Performance's S55 Power Control Module has distinct calibrations for the supported M2 Competition, M2 CS, M3 and M4 variants. A vehicle-specific loom and bracket support a removable installation. Match the selected calibration to the original model and trim.Key features Vehicle-specific hardware calibration for...

For an N54 build seeing repeated boost, charge-air consistency matters as much as peak output. MMX Performance's bar-and-plate intercooler increases core volume and uses OE-style pipe connections. Its fitment is engine-specific, not universal to every 135i or 335i.Key features Bar-and-plate core with more than...

Retain the matching OEM JCW front calipers with an MMX Performance directional floating rotor pair. The 335 x 30mm discs use aluminum hats and 48 curved cooling vanes. A JCW badge or styling package alone does not confirm the required brake system.Key features Floating...

The MMX Performance rear rotor kit includes more than discs. Its 325 x 10mm floating rotors come with the matched red caliper carriers for the specified JCW setup. Check the parking-brake arrangement first: electric-handbrake variants are excluded.Key features Floating two-piece rear rotor upgrade. Aluminum...

The MMX Performance F8X sump focuses on oil around the gears, not only temperature outside the housing. Its wide windage tray supports lubrication and accommodates Drexler and mechanical limited-slip differentials without trimming. Extra capacity, fins and an external-cooler port complete the package.Key features Adds...

This is the complete MMX Performance G8X differential package: mounting, oil control and driveshaft heat protection. It adds the high-capacity sump and heat shields to the four-point mounting arrangement. Install at standard height or use the matched 10mm raised setting for a lowered vehicle.Key...

Get adjustable ride height without replacing compatible adaptive M dampers. The MMX Performance F8X spring kit provides separate front and rear adjustment ranges to balance stance and clearance. Progressive springs support a lower setup while retaining usable road manners.Key features Height adjustment allows the...

A directional rotor needs the correct disc on each side. This MMX Performance front pair supplies left- and right-handed 380 x 36mm discs with floating aluminum hats and curved cooling vanes. It retains the matching factory caliper layout rather than creating a big-brake conversion.Key...

The MMX Performance front carbon-ceramic pair changes rotor material while keeping the supported 380 x 36mm dimensions. Its drilled, two-piece floating construction replaces the referenced steel setup. Match the caliper and ceramic-compatible pads rather than assuming every factory ceramic system uses this size.Key features...

These MMX Performance 370 x 24mm rear carbon-ceramic rotors upgrade the supported factory steel-brake setup. A two-piece floating arrangement combines with a multidirectional carbon-ceramic matrix. Ceramic-compatible pads and correct brake-package identification are essential.Key features Carbon-ceramic construction reduces weight compared with the original steel rotors....

Choose this MMX package to improve the complete intake path while retaining the factory airboxes. Turbo elbows, intake pipes and replacement panel filters upgrade those sections together. Unlike a carbon airbox kit, the original airbox housings remain part of the system.Key features Machined, mandrel-bent...

A direct-fit intake can add induction sound without replacing the factory cold-air feed. This MMX Performance kit places a cotton filter behind a dedicated heat shield and uses the original mounting points. The pre-LCI application scope covers the supported 1.5-liter and 2.0-liter engines, with...

Differential movement and driveshaft angle are related, but they are not the same problem. The MMX Performance front cradle reduces movement at standard height. With the correct rear components, it also supports a raised setup for lowered cars. Those companion parts differ between F8X...

The S55 charge-air system needs both turbo-side pipes and a path from the chargecooler to the throttle body. This MMX Performance kit addresses both sections with aluminum hard pipes and sealed connections. It replaces the complete pipework path rather than one tube in an...

Repeated boost runs raise charge-air temperature. MMX Performance uses a stepped tube-and-fin core in this pre-LCI intercooler kit to address cooling without unnecessary pressure loss. Separate Cooper S and JCW configurations match the cooler to the original trim.Key features Stepped tube-and-fin core increases cooling...

Underbody bracing connects mounting points that work as the chassis loads up through a corner. This MMX Performance set replaces the three original braces on supported platforms with profiled billet aluminum parts. The kit also adds exhaust clearance and uses the existing body mounting...

Track use puts repeated heat and load into the rear drivetrain. This MMX Performance package combines a larger baffled differential sump, a dual differential mount and output-shaft heat shields. The bundle brings those cooling and support upgrades together without adding the front cradle supplied...

Fixed lowering springs offer one ride height. This MMX Performance height-adjustable kit lets the installer set front and rear height within its adjustment range while retaining compatible adaptive M dampers. That helps balance stance and clearance rather than guessing from a quoted drop.Key features...

Retain compatible factory airboxes while replacing the corrugated intake path to the turbo inlets. The MMX Performance pipe kit uses constant-diameter aluminum pipework and sealed billet adapters to remove abrupt transitions. It suits a build that wants an improved intake path without a complete...